will install a command line utility embd which will allow you to quickly get started with prototyping. The binary should be available in your $GOPATH/bin. However, to be able to run this on a ARM based device, you will need to build it with GOOS=linux and GOARCH=arm environment variables set.

But, since I am feeling so generous, a prebuilt/tested version is available for direct download and deployment here.

For example, if you run embd detect on a BeagleBone Black:

root@beaglebone:~# embd detect

detected host BeagleBone Black (rev 0)

Run embd without any arguments to discover the various commands supported by the utility.

How to use the framework

Package embd provides a hardware abstraction layer for doing embedded programming on supported platforms like the Raspberry Pi and BeagleBone Black. Most of the examples below will work without change (i.e. the same binary) on all supported platforms. How cool is that?

Although samples are all present in the samples folder, we will show a few choice examples here.

Use the LED driver to toggle LEDs on the BBB:

import "github.com/kidoman/embd"
...
embd.InitLED()
defer embd.CloseLED()
...
led, err := embd.NewLED("USR3")
...
led.Toggle()

Even shorter while prototyping:

import "github.com/kidoman/embd"
...
embd.InitLED()
defer embd.CloseLED()
...
embd.ToggleLED(3)

NB: 3 == USR3 for all intents and purposes. The driver is smart enough to figure all this out.

BBB + PWM:

import "github.com/kidoman/embd"
...
embd.InitGPIO()
defer embd.CloseGPIO()
...
pwm, _ := embd.NewPWMPin("P9_14")
defer pwm.Close()
...
pwm.SetDuty(1000)

Control GPIO pins on the RaspberryPi / BeagleBone Black:

import "github.com/kidoman/embd"
...
embd.InitGPIO()
defer embd.CloseGPIO()
...
embd.SetDirection(10, embd.Out)
embd.DigitalWrite(10, embd.High)

Could also do:

import "github.com/kidoman/embd"
...
embd.InitGPIO()
defer embd.CloseGPIO()
...
pin, err := embd.NewDigitalPin(10)
...
pin.SetDirection(embd.Out)
pin.Write(embd.High)

Or read data from the Bosch BMP085 barometric sensor:

import "github.com/kidoman/embd"
import "github.com/kidoman/embd/sensor/bmp085"
...
bus := embd.NewI2CBus(1)
...
baro := bmp085.New(bus)
...
temp, err := baro.Temperature()
altitude, err := baro.Altitude()

Even find out the heading from the LSM303 magnetometer:

import "github.com/kidoman/embd"
import "github.com/kidoman/embd/sensor/lsm303"
...
bus := embd.NewI2CBus(1)
...
mag := lsm303.New(bus)
...
heading, err := mag.Heading()

The above two examples depend on I2C and therefore will work without change on almost all platforms.

Protocols Supported

Digital GPIO Documentation
Analog GPIO Documentation
PWM Documentation
I2C Documentation
LED Documentation

Sensors Supported

TMP006 Thermopile sensor Documentation, Datasheet, Userguide
BMP085 Barometric pressure sensor Documentation, Datasheet
BMP180 Barometric pressure sensor Documentation, Datasheet
LSM303 Accelerometer and magnetometer Documentation, Datasheet
L3GD20 Gyroscope Documentation, Datasheet
US020 Ultrasonic proximity sensor Documentation, Product Page
BH1750FVI Luminosity sensor Documentation, Datasheet

Interfaces

Keypad(4x3) Product Page

Controllers

PCA9685 16-channel, 12-bit PWM Controller with I2C protocol Documentation, Datasheet, Product Page
MCP4725 12-bit DAC Documentation, Datasheet, Product Page
ServoBlaster RPi PWM/PCM based PWM controller Documentation, Product Page

Contributing

We look forward to your pull requests, but contributions which abide by the guidelines will get a free beer!

File an issue, open a pull request. We are waiting.

About

EMBD is affectionately designed/developed by Karan Misra (kidoman), Kunal Powar (kunalpowar) and FRIENDS.