* g10/gpg.c: New option --allow-old-cipher-algos.
(set_compliance_option): Set --rfc4880bis explictly to SHA256 and
AES256. Allow old cipher algos for OpenPGP, rfc4880, and rfc2440.
* g10/options.h (opt): Add flags.allow_old_cipher_algos.
* g10/misc.c (print_sha1_keysig_rejected_note): Always print the note
unless in --quiet mode.
* g10/encrypt.c (setup_symkey): Disallow by default algos with a
blocklengt < 128.
(encrypt_crypt): Ditto. Fallback by default to AES instead of 3DES.
* g10/pkclist.c (algo_available): Take care of old cipher also.
(select_algo_from_prefs): Use AES as implicit algorithm by default.
* tests/openpgp/defs.scm (create-gpghome): Set allow-old-cipher-algos.
--
GnuPG-bug-id: 3415
* tools/symcryptrun.c: Remove.
* tools/Makefile.am: Ditto.
* doc/tools.texi: Remove man page.
* configure.ac: Remove build option and tests used only by this tool.
* Makefile.am (AM_DISTCHECK_CONFIGURE_FLAGS): Do not build
symcryptrun.
--
symcryptrun is too ancient to be of any use and has not been tested in
many years. Thus we should not distribute it anymore.
* g10/gpg.c (oPrintPKARecords): Remove.
(opts): Remove --print-pka-records.
(main): Remove "pka-lookups","pka-trust-increase" and other PKA stuff.
* g10/options.h (EXPORT_DANE_FORMAT): Remove.
(VERIFY_PKA_LOOKUPS, VERIFY_PKA_TRUST_INCREASE): Remove.
(KEYSERVER_HONOR_PKA_RECORD): Remove.
* g10/packet.h (pka_info_t): Remove.
(PKT_signature): Remove flags.pka_tried and pka_info.
* g10/parse-packet.c (register_known_notation): Remove
"pka-address@gnupg.org".
* g10/pkclist.c (check_signatures_trust): Remove PKA stuff.
* g10/call-dirmngr.c (gpg_dirmngr_get_pka): Remove.
* g10/export.c (parse_export_options): Remove "export-pka".
(do_export): Adjust for this.
(write_keyblock_to_output): Ditto.
(do_export_stream): Ditto.
(print_pka_or_dane_records): Rename to ...
(print_dane_records): this and remove two args. Remove PKA printing.
* g10/free-packet.c (free_seckey_enc, cp_pka_info): Adjust for removed
pka_info field.
* g10/getkey.c (get_pubkey_byname): Make AKL_PKA a dummy.
* g10/keyserver.c: Remove "honor-pka-record".
(keyserver_import_pka): Remove.
* g10/mainproc.c (get_pka_address): Remove.
(pka_uri_from_sig): Remove.
(check_sig_and_print): Remove code for PKA.
--
PKA (Public Key Association) was a DNS based key discovery method
which looked up fingerprint by mail addresses in the DNS. This goes
back to the conference where DKIM was suggested to show that we
already had a better method for this available with PGP/MIME. PKA was
was later superseded by an experimental DANE method and is today not
anymore relevant. It is anyway doubtful whether PKA was ever widely
used.
Signed-off-by: Werner Koch <wk@gnupg.org>
--
With these modifications it is now possible to store and retrieve keys
from an AD without manually tweaking the schema. Permissions need to
be set manuallay, though.
--
I accidently added a gpgSubCertID attribute not realizing that the
pgpSubKeyID already carries the long keyid. Remove that. Note that
the pgpkeyID has the short keyid and the long keyid has the name
pgpCertID.
Signed-off-by: Werner Koch <wk@gnupg.org>
* dirmngr/ks-engine-ldap.c (SERVERINFO_): New constants.
(my_ldap_connect): Relace args pgpkeyattrp and real_ldapp by a new
serverinfo arg. Set the new info flags.
(ks_ldap_get): Adjust for change.
(ks_ldap_search): Ditto.
(ks_ldap_put): Ditto. Replace xmalloc by xtrymalloc. Change the DN
for use with NTDS (aka Active Directory).
* doc/ldap/gnupg-ldap-init.ldif (pgpSoftware): Update definition of
pgpVersion.
* doc/ldap/gnupg-ldap-ad-init.ldif: New.
* doc/ldap/gnupg-ldap-ad-schema.ldif: New.
--
This is a first take on better Active Directory support. The main
change for NTDS in the code is that the an top-RDN of CN is used
instead of the old pgpCertID. More changes to come; for example using
and storing the fingerprint.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/gpg.texi: Add parameters for batch generation of ECC keys.
--
There are parameters required for batch generation of ECC keys which
weren't mentioned in the documentation.
Signed-off-by: Jens Meißner <meissner@b1-systems.de>
* scd/app.c (is_same_serialno): New.
(check_application_conflict): Use this.
(select_application): Ditto.
(app_switch_current_card): Ditto.
* scd/app-openpgp.c (check_keyidstr): Ignore the card version and also
compare case insensitive.
--
This is required because we change what we emit as serialno of OpenPGP
cards but existing keys still use the old form of the serial
number (i.e. with a firmware version).
See-commit: 3a8250c020
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/keydb.h (pref_hint): Change from union to struct and add field
'exact'. Adjust callers.
* g10/pkclist.c (algo_available): Take care of the exact hint.
* g10/sign.c (sign_file): Rework the hash detection from
recipient prefs.
--
This fixes a encrypt+sign case like: One recipient key has SHA512 as
highest ranked hash preference but the the signing key is a 256 bit
curve. Because we don't want to use a truncated hash with ECDSA, we
need to have an exact match - this is in particular important for
smartcard which check that the hash matches the curves.
Signed-off-by: Werner Koch <wk@gnupg.org>
Ported-from-stable: aeed0b93ff
* scd/command.c (reset_notify): Add option --keep-lock.
(do_reset): Add arg keep_lock.
(cmd_lock): Send progress status.
* g10/call-agent.c (agent_scd_apdu): Add more pseudo APDUs.
* g10/card-util.c (send_apdu): Ditto.
(factory_reset): Use lock commands.
--
This is required so that for example Kleopatra does not detect the
RESET and issues a SERIALNO of its own, thus conflicting with our
SERIALNO undefined.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/examples/vsnfd.prf: Rename to VS-NfD.prf.
* doc/examples/Automatic.prf: New.
* doc/Makefile.am (examples): Adjust.
* build-aux/speedo/w32/inst.nsi: Install gpg-check-pattern.exe and 3
example files.
* build-aux/speedo/w32/wixlib.wxs: Add new files.
--
Note that we renamed the existing example profile so that kleopatra
shows a nicer name. In fact the gpg4win installer just copies of
theses file but it is better to maintain them here.
gpg-check-pattern.exe can no be installed because we meanwhile have a
regex lib which works also on Windows.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (parse_list_options): Add "sort-sigs".
(main): Make it the default.
* g10/options.h (LIST_SORT_SIGS): New.
* g10/keylist.c (cmp_signodes): New.
(list_keyblock_print): Sort signatures and factor signature printing
code out to ...
(list_signature_print): new.
--
In particular together with --full-timestamps this makes it easier to
see the history of key signatures and their revocations. The
self-signatures are also printed first. To disable this
--list-options no-sort-sigs
can be used.
Also don't print the annoying "no recocation reason specified"
message.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/examples/vsnfd.prf: Remove enable-extended-key-format
--
This is no longer a valid option for gpg-agent because it
is now the default.
(cherry picked from commit d833030f8c)
* g10/options.h (IMPORT_BULK): New.
* g10/import.c (parse_import_options): Add "bulk-import".
* g10/call-keyboxd.c (in_transaction): New var.
(gpg_keyboxd_deinit_session_data): Run a commit if in bulk import
mode.
(create_new_context): Run a begin transaction if in bulk import mode.
--
Initial tests with this option are not very promising. Importing
about 3000 real world keys with --use-keyboxd and full logging took:
real 33m31.724s
user 19m54.265s
sys 2m49.662s
With bulk-import this saves a mere 12%:
real 29m36.542s
user 19m3.391s
sys 2m46.728s
Signed-off-by: Werner Koch <wk@gnupg.org>
* kbx/backend-sqlite.c (table_definitions): Add column UINO to
userids.
(be_sqlite_local_s): Add fields select_col_uidno and
select_col_subkey.
(run_select_statement): Also select subkey or uidno column.
(be_sqlite_search): Return their values.
(store_into_userid): Store the UIDNO.
* kbx/backend-support.c (be_return_pubkey): Extend PUBKEY_INFO.
--
For an existing database adding the new column to the table userid is
straightforward. However if the original version of the schema used an
integer for the keyid column, that column has likely be renamed. Make
sure that the NOT NULL constraint has also be removed; check the
SQLite documentation on how this can be done.
Signed-off-by: Werner Koch <wk@gnupg.org>
* scd/app-openpgp.c (send_keypair_info): Emit the algo string as part
of a KEYPAIRINFO.
* scd/command.c (do_readkey): Ditto.
* scd/app-piv.c (do_readkey): Ditto.
* scd/app-nks.c (do_learn_status_core): Ditto.
(struct fid_cache_s): Add field algostr.
(flush_fid_cache): Release it.
(keygripstr_from_pk_file): Fill it and add it to the cache. Use a
single exit label.
* scd/app-help.c (app_help_get_keygrip_string_pk): Add new arg
r_algostr. Change all callers.
--
This is helpful so that callers do not need to parse the key for this
basic information. Use "scd readkey --info-only" to return the info
status line instead of the key material; using just --info returns the
info in addition to the key material.
Signed-off-by: Werner Koch <wk@gnupg.org>
* kbx/backend-support.c (be_return_pubkey): Add args is_ephemeral and
is_revoked. Adjust callers.
* kbx/backend-sqlite.c: Alter table pubkey to add new columns.
(run_select_statement): Add new column to all selects.
(be_sqlite_search): Return the new flags.
--
For existing test databases the new column can be added with:
alter table pubkey add ephemeral integer not null default 0;
alter table pubkey add revoked integer not null default 0;
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/gnupg-module-overview.svg: Add examples of GPGME aware
applications
--
Whenever I used this overview I needed to explain what this
meant so giving examples might help a bit and also illustrate
the codesharing between GpgOL, Kleopatra and KMail.
* scd/app-openpgp.c (data_objects): 0x00FA for binary data.
(do_getattr): Parse the data and send it in status lines.
(get_algorithm_attribute_string): New.
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
* tools/gpgtar.c (oUtf8Strings): New.
(opts): Add option --utf8-strings.
(parse_arguments): Set option.
* tools/gpgtar.h (opt): Add field utf8strings.
* tools/gpgtar-create.c (name_to_utf8): New.
(fillup_entry_w32): Use that.
(scan_directory): Ditto.
(scan_directory) [W32]: Convert file name to utf8.
(gpgtar_create): Convert pattern.
--
Note that this works only with file names read from a file or if the
specified files on the command line are plain ascii. When recursing
into a directory Unicode file names work again. This limitation is
due to main(int, char**) which can't get the wchar version. We could
fix that but is needs a bit more work in our init code.
GnuPG-bug-id: 4083
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oChUid): New.
(opts): Add --chuid.
(main): Implement --chuid. Delay setting of homedir until the new
chuid is done.
* sm/gpgsm.c (main): Delay setting of homedir until the new chuid is
done.
* tools/gpg-card.c (oChUid): New.
(opts): Add --chuid.
(changeuser): New helper var.
(main): Implement --chuid.
* tools/gpg-connect-agent.c (oChUid): New.
(opts): Add --chuid.
(main): Implement --chuid.
--
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/gpgsm.c (oChUid, opts): New option --chuid.
(main): Implement option.
--
This option will at least be useful for Scute.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/keylist.c (list_cert_colon): Emit a new "fp2" record.
(list_cert_raw): Print the SHA2 fingerprint.
(list_cert_std): Ditto.
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/gpgrlhelp.c (read_write_history): New.
(gnupg_rl_initialize): Register new function.
* common/ttyio.c (my_rl_rw_history): New var.
(tty_private_set_rl_hooks): Add arg read_write_history.
(tty_read_history): New.
(tty_write_history): New.
* tools/gpg-card.c (HISTORYNAME): New.
(oNoHistory): New enum value.
(opts): New option --no-history.
(cmd_history): New.
(cmds): New command "history".
(interactive_loop): Read and save the history.
* tools/gpg-connect-agent.c (HISTORYNAME): New.
(opts): New option --no-history.
(main): Read and save the history. New command /history.
--
Yeah, finally we have stored history; I should have added this much
earlier.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/pkclist.c (write_trust_status): Add arg mbox.
(check_signatures_trust): Appenmd mbox to the status lines.
--
GnuPG-bug-id: 4735
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/mainproc.c (check_sig_and_print): Add failsafe check for PK.
Pass KEYBLOCK down do check_signatures_trust. Protect existsing error
ocde in case the signature expired.
* g10/pkclist.c (is_in_sender_list): New.
(check_signatures_trust): Add args keyblock and pk. Add new uid based
checking code.
* g10/test-stubs.c, g10/gpgv.c: Adjust stubs.
--
GnuPG-bug-id: 4735
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/gpg-card.c: Include tlv.h.
(cmd_writecert): Add option --openpgp.
(cmd_readcert): Ditto.
--
We use the CERT object for this and encapsulate the key block in a CMS
object.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/fingerprint.c (gpgsm_get_key_algo_info): Factor code out to ...
(gpgsm_get_key_algo_info2): new.
(gpgsm_pubkey_algo_string): New.
* sm/keylist.c (list_cert_colon): Put curve into field 17
(list_cert_raw): Print the unified key algotithm string instead of the
algo and size.
(list_cert_std): Ditto.
--
It is important to known whether a 256 bit ECC uses a NIST or a
Brainpool curve.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/certchain.c (find_up): Disable external lookups in offline mode.
Always allow AKI lookup if CRLs are also enabled.
--
GnuPG-bug-id: 4898
Signed-off-by: Werner Koch <wk@gnupg.org>
* scd/app-openpgp.c (get_manufacturer): New..
(do_getattr): Add new attribute "MANUFACTURER".
(do_learn_status): Always print it.
--
This will make it easy to maintain the list of OpenPGP vendors at just
one place.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/certchain.c (is_cert_still_valid): Shortcut if tehre is no DP.
* common/audit.c (proc_type_verify): Print "n/a" if a cert has no
distribution point.
* sm/gpgsm.h (opt): Add field enable_issuer_based_crl_check.
* sm/gpgsm.c (oEnableIssuerBasedCRLCheck): New.
(opts): Add option --enable-issuer-based-crl-check.
(main): Set option.
--
If the issuer does not provide a DP and the user wants such an issuer,
we expect that a certificate does not need revocation checks. The new
option --enable-issuer-based-crl-check can be used to revert to the
old behaviour which requires that a suitable LDAP server has been
configured to lookup a CRL by issuer.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/trustdb.c (tdb_register_trusted_key): accept fingerprint as well
as long key ID.
* doc/gpg.texi: document that --trusted-key can accept a fingerprint.
--
GnuPG-bug-id: 4855
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
Fixed uses or return and kept the old string to avoid breaking
translations.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (opts): New options --auto-key-import,
--no-auto-key-import, and --no-include-key-block.
(gpgconf_list): Add them.
* g10/options.h (opt): Add field flags.auto_key_import.
* g10/mainproc.c (check_sig_and_print): Use flag to enable that
feature.
* tools/gpgconf-comp.c: Give the new options a Basic config level.
--
Note that the --no variants of the options are intended for easy
disabling at the command line.
GnuPG-bug-id: 4856
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/openpgpdefs.h (SIGSUBPKT_KEY_BLOCK): New.
* g10/gpg.c (oIncludeKeyBlock): New.
(opts): New option --include-key-block.
(main): Implement.
* g10/options.h (opt): New flag include_key_block.
* g10/parse-packet.c (dump_sig_subpkt): Support SIGSUBPKT_KEY_BLOCK.
(parse_one_sig_subpkt): Ditto.
(can_handle_critical): Ditto.
* g10/sign.c (mk_sig_subpkt_key_block): New.
(write_signature_packets): Call it for data signatures.
--
This patch adds support for a to be proposed OpenPGP ferature:
Introduce the Key Block subpacket to align OpenPGP with CMS.
This new subpacket may be used similar to the CertificateSet of
CMS (RFC-5652) and thus allows to start encrypted communication
after having received a signed message. In practice a stripped down
version of the key should be including having only the key material
and the self-signatures which are really useful and shall be used by
the recipient to reply encrypted.
#### Key Block
(1 octet with value 0, N octets of key data)
This subpacket MAY be used to convey key data along with a signature
of class 0x00, 0x01, or 0x02. It MUST contain the key used to create
the signature; either as the primary key or as a subkey. The key
SHOULD contain a primary or subkey capable of encryption and the
entire key must be a valid OpenPGP key including at least one User ID
packet and the corresponding self-signatures.
Implementations MUST ignore this subpacket if the first octet does not
have a value of zero or if the key data does not represent a valid
transferable public key.
GnuPG-bug-id: 4856
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/export.c (push_export_filters): New.
(pop_export_filters): New.
(export_pubkey_buffer): Add args prefix and prefixlen. Adjust
callers.
* g10/import.c (impex_filter_getval): Add property "fpr".
* g10/main.h (struct impex_filter_parm_s): Add field hexfpr.
--
The push and pop feature will help us to use the export filter
internally in gpg. Same for the export_pubkey_buffer change.
GnuPG-bug-id: 4856
Signed-off-by: Werner Koch <wk@gnupg.org>
No functional changes, just fixing minor spelling issues.
---
Most of these were identified from the command line by running:
codespell \
--ignore-words-list fpr,stati,keyserver,keyservers,asign,cas,iff,ifset \
--skip '*.po,ChangeLog*,help.*.txt,*.jpg,*.eps,*.pdf,*.png,*.gpg,*.asc' \
doc g13 g10 kbx agent artwork scd tests tools am common dirmngr sm \
NEWS README README.maint TODO
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* scd/app-openpgp.c (send_keypair_info): Reaturn the key creation time
as part of a KEYPAIRINFO.
(do_readkey): Do not return the KEY-TIME anymore.
--
Sending the KEY_TIME status as part of a READKEY command was only
recently added. It is better to merge that into the KEYPAIRINFO line.
Another patch with chnage this for the consumers of that info.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/watchgnupg.c: Include sys/wait.h.
(GNUPG_DEF_COPYRIGHT_LINE): Add a default value for standalone
building.
(get_logname): New.
(main): Use a default socket name and add option --homedir.
--
This is quite convenient and saves a lot of typing or shell alias
definitions.
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/util.h (UBID_LEN): New. Use it at all places.
* kbx/keybox-blob.c (create_blob_finish): Do not write the UBID item.
* kbx/keybox-dump.c (print_ubib): Remove.
(_keybox_dump_blob): Do not print the now removed ubid flag.
* kbx/keybox-search-desc.h (struct keydb_search_desc): Use constants
for the size of the ubid and grip.
* kbx/keybox-search.c (blob_cmp_ubid): New.
(has_ubid): Make it a simple wrapper around blob_cmp_ubid.
(keybox_get_data): Add arg 'r_ubid'.
* kbx/frontend.h (enum kbxd_store_modes): New.
* kbx/kbxserver.c (cmd_store): Add new option --insert.
* kbx/backend-cache.c (be_cache_initialize): New.
(be_cache_add_resource): Call it here.
* kbx/backend-kbx.c (be_kbx_seek): Remove args 'fpr' and 'fprlen'.
(be_kbx_search): Get the UBID from keybox_get_data.
* kbx/backend-support.c (be_fingerprint_from_blob): Replace by ...
(be_ubid_from_blob): new. Change all callers.
* kbx/frontend.c (kbxd_add_resource): Temporary disable the cache but
use the new cache init function.
(kbxd_store): Replace arg 'only_update' by 'mode'. Seek using the
ubid. Take care of the mode.
--
It turned out that using the hash of the entire blob was not helpful.
Thus we redefine the Unique-Blob-ID (UBID) as the primary fingerprint
of the blob. In case this is a v5 OpenPGP key a left truncated
version of the SHA-256 hash is used; in all other cases the full SHA-1
hash. Using a SHA-256 hash does not make sense because v4 keys are
and will for some time be the majority of keys and thus padding them
with zeroes won't make any difference. Even if fingerprint collisions
can eventually be created we will assume that the keys are bogus and
that it does not make sense to store its twin also in our key storage.
We can also easily extend the update code to detect a collision and
reject the update.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/DETAILS: Specify new status code "NOTE".
* dirmngr/ks-engine-http.c (ks_http_fetch): Print a NOTE status for a
bad TLS certificate.
* g10/call-dirmngr.c (ks_status_cb): Detect this status.
--
For example a
gpg -v --locate-external-keys dd9jn@posteo.net
now yields
gpg: Note: server uses an invalid certificate
gpg: (further info: bad cert for 'posteo.net': \
Hostname does not match the certificate)
gpg: error retrieving 'dd9jn@posteo.net' via WKD: Wrong name
gpg: error reading key: Wrong name
(without -v the "further info" line is not shown). Note that even
after years Posteo is not able to provide a valid certificate for
their .net addresses. Anyway, this help to show the feature.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/gpgsm.h (struct keyserver_spec): Add field use_ldaps.
* sm/gpgsm.c (parse_keyserver_line): Parse flags.
* sm/call-dirmngr.c (prepare_dirmngr): Send ldaps flag to the dirmngr.
* dirmngr/dirmngr.h (struct ldap_server_s): Add field use_ldaps.
* dirmngr/ldapserver.c (ldapserver_parse_one): Parse flags.
* dirmngr/ldap.c (start_cert_fetch_ldap): Call wrapper with --tls.
* dirmngr/dirmngr_ldap.c: New option --tls.
(fetch_ldap): Make use of that option.
--
There was no way to specify an LDAPS server in
dirmngr_ldapserver.socnf or with gpgsm's --keyserver option. This
patch fixes this. Eventually we should allow to replace host and port
by a partial URI in the same way ldap_initialize does it. For backward
compatibility we do not yet do that.
Although the dirmngr code accepts an URL (eg. taken from a
certificate), I can't see how the scheme was ever used. Thus the
patch also detects an ldaps scheme and uses this. That part has not
been tested, though.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/import.c (import_one_real): Don't do the final clean in the
merge case.
--
This fixes a regression introduced with self-sigs-only.
GnuPG-bug-id: 4628
Signed-off-by: Werner Koch <wk@gnupg.org>
--
Resolved Conflicts:
* common/asshelp.c: Keep the new code in master for spawing under
Windows.
* g10/Makefile.am: Keep all new file.
* g10/photoid.c: Pass CTRL to pct_expando.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/Makefile.am (EXTRA_DIST, BUILT_SOURCES): Add
gnupg-module-overview.eps, gnupg-card-architecture.eps
(DISTCLEANFILES): Remove them.
--
The files needs to be added so that it is properly
included in the dist tarball. As the rule
for it was moved into maintainer mode by 58bab1a.
* g10/keygen.c (parse_key_parameter_part): Add arg R_KEYGRIP and
support the special algo "card".
(parse_key_parameter_string): Add args R_KEYGRIP and R_SUBKEYGRIP.
Handle the "card" algo. Adjust callers.
(parse_algo_usage_expire): Add arg R_KEYGRIP.
(quickgen_set_para): Add arg KEYGRIP and put it into the parameter
list.
(quick_generate_keypair): Handle algo "card".
(generate_keypair): Also handle the keygrips as returned by
parse_key_parameter_string.
(ask_algo): Support ed25519 from a card.
--
Note that this allows to create a new OpenPGP key from an initialized
OpenPGP card or from any other supported cards. It has been tested
with the TCOS Netkey card. Right now a stub file for the cards might
be needed; this can be achieved by running "gpgsm --learn" with the
card plugged in.
Example:
gpg --quick-gen-key foo@example.org card
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/keygen.c (ask_algo): Identify the standard keys.
--
The asterisks mark the usages of a key as retruned by scd via the
$AUTHKEYID et al. attributes.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (opts): Add option.
(main): Set flag.
* g10/options.h: Add flags.use_only_openpgp_card.
* g10/call-agent.c (start_agent): Implement option.
--
With the previous patch we switch to autoselect an application
instead of requesting an openpgp card. This option allows to revert
this in case of use use cases which expected the former behaviour.
Signed-off-by: Werner Koch <wk@gnupg.org>
(cherry picked from commit c185f6dfbd)
This was first added to the 2.2 branch.
* doc/gpg-agent.texi: improve documentation of CARD entry in
GETEVENTCOUNTER description.
--
"stati" is unclear and confusing, and describing something in the
singular is almost always less ambiguous than leaving it in the
plural.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* configure.ac: New option --keyboxd-pgm.
(KEYBOXD_NAME, KEYBOXD_DISP_NAME): New ac_defines.
* common/util.h: Add substitutes for new error codes.
(GNUPG_MODULE_NAME_KEYBOXD): New.
* common/homedir.c (gnupg_module_name): Support
GNUPG_MODULE_NAME_KEYBOXD.
* common/asshelp.c (SECS_TO_WAIT_FOR_KEYBOXD): New.
(wait_for_sock): Support keyboxd.
(start_new_service): Ditto.
(start_new_keyboxd): New.
* tools/gpg-connect-agent.c: New options --keyboxd and
--keyboxd-program.
(start_agent): Implement new option.
--
This change allows us to test the new keyboxd using our standard
helper. It also provides the necessary code to start keyboxd on the
fly.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/mainproc.c (check_sig_and_print): Print a hint on how to make
use of the preferred keyserver. Remove keyserver lookup just by the
keyid. Try a WKD lookup before a keyserver lookup.
--
The use of the the keyid for lookups does not make much sense anymore
since for quite some time we do have the fingerprint as part of the
signature.
GnuPG-bug-id: 4595
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (main): Change default.
--
Due to the DoS attack on the keyeservers we do not anymore default to
import key signatures. That makes the keyserver unsuable for getting
keys for the WoT but it still allows to retriev keys - even if that
takes long to download the large keyblocks.
To revert to the old behavior add
keyserver-optiions no-self-sigs-only,no-import-clean
to gpg.conf.
GnuPG-bug-id: 4607
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (aLocateExtKeys): New.
(opts): Add --locate-external-keys.
(main): Implement that.
* g10/getkey.c (get_pubkey_byname): Implement GET_PUBKEY_NO_LOCAL.
(get_best_pubkey_byname): Add arg 'mode' and pass on to
get_pubkey_byname. Change callers.
* g10/keylist.c (public_key_list): Add arg 'no_local'.
(locate_one): Ditto. Pass on to get_best_pubkey_byname.
--
This new command is a shortcut for
--auto-key-locate nodefault,clear,wkd,... --locate-key
and uses the default or configured AKL list but does so without local.
See also
GnuPG-bug-id: 4599
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/options.h (IMPORT_SELF_SIGS_ONLY): New.
* g10/import.c (parse_import_options): Add option "self-sigs-only".
(read_block): Handle that option.
--
This option is intended to help against importing keys with many bogus
key-signatures. It has obvious drawbacks and is not a bullet-proof
solution because a self-signature can also be faked and would be
detected only later.
GnuPG-bug-id: 4591
Signed-off-by: Werner Koch <wk@gnupg.org>
A new user who sees "policy-file" and searches naively through the
documentation to find it again won't be able to tell what this refers
to, since "policies.txt" doesn't otherwise match the search string
"policy". This gives them a fighting chance at finding the
documentation.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* doc/scdaemon.texi (card-timeout): Remove.
* scd/scdaemon.c (main): Remove oCardTimeout handling.
--
There was the card-timeout option in GnuPG 2.0, but it was never
implemented correctly. The intention of this option was to allow
sharing smartcard among multiple applications, but this didn't work
well as user's expectation (it only worked with DISCONNECT command).
This is because other parts of scdaemon assumes exclusive access. In
GnuPG 2.1, the support of the option was removed, improving
"DISCONNECT" command always works well without this option.
GnuPG-bug-id: 3383
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
* common/userids.c (classify_user_id): Do not set the EXACT flag in
the default case.
* g10/export.c (exact_subkey_match_p): Make static,
* g10/delkey.c (do_delete_key): Implement subkey only deleting.
--
GnuPG-bug-id: 4457
* g10/options.h (opt): Add flags.dummy_outfile.
* g10/decrypt.c (decrypt_message): Set this global flag instead of the
fucntion local flag.
* g10/plaintext.c (get_output_file): Ignore opt.output if that was
used as a dummy option aslong with --use-embedded-filename.
--
The problem here was that an explicit specified --decrypt, as
meanwhile suggested, did not work with that dangerous
--use-embedded-filename. In contrast it worked when gpg decrypted as
a side-effect of parsing the data.
GnuPG-bug-id: 4500
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/exec.c (w32_system): Add "!ShellExecute" special.
* g10/photoid.c (get_default_photo_command): Use the new ShellExecute
under Windows and fallbac to 'display' and 'xdg-open' in the Unix
case.
(show_photos): Flush stdout so that the output is shown before the
image pops up.
--
For Unix this basically syncs the code with what we have in gpg 1.4.
Note that xdg-open may not be used when running as root which we
support here.
For Windows we now use ShellExecute as this seems to be preferred over
"cmd /c start"; however this does not solve the actual problem we had
in the bug report. To solve that problem we resort to a wait
parameter which defaults to 400ms. This works on my Windows-10
virtualized test box. If we can figure out which simple viewers are
commonly installed on Windows we should enhance this patch to test for
them.
GnuPG-bug-id: 4334
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/sign.c (make_keysig_packet): Remove obsolete arg diegst_algo
which was always passed as 0. Change all callers.
* g10/gpgcompose.c (signature): Warn when trying to set a digest algo.
--
Signed-off-by: Werner Koch <wk@gnupg.org>
--
Getting the rendering of man pages is not really easy; let's see
whether this is better. The change has also been done upstream.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/call-agent.c (agent_scd_readkey): New.
* g10/keygen.c (ask_key_flags): Factor code out to ..
(ask_key_flags_with_mask): new.
(ask_algo): New mode 14.
--
Note that this new menu 14 is always displayed. The usage flags can
be changed only in --expert mode, though. Creating and using signing
keys works but decryption does not yet work; we will need to tweak a
couple of other places for that. Tested with a Yubikey's PIV app.
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/gpgv.texi: Improve documentation for keyring choices
--
From the existing documentation, it's not clear whether the default
keyring will always be mixed into the set of keyrings, or whether it
will be skipped if a --keyring is present. The updated text here
attempts to describe the keyring selection logic more completely.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* tools/gpgtar-create.c (gpgtar_create): Switch to the -C directory.
--
The -C option is pretty useful given that pattern are always relative
to the current directory. In contrast to GNU tar, the switching is
done only once.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/gpg-agent.c (oEnableExtendedKeyFormat): Re-introduce.
(parse_rereadable_options): Handle it in a special way.
* agent/protect.c (agent_protect): Be safe and set use_ocb only to 1
or 0.
* tools/gpgconf-comp.c: Add --enable-extended-key-format again.
--
This is required for backward compatible with profiles.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/gpg-agent.c (oDisableExtendedKeyFormat, oNoop): New.
(oEnableExtendedKeyFormat): Remove.
(opts): Make --enable-extended-key-format a dummy option. Add
disable-extended-key-format.
(parse_rereadable_options): Implement oDisableExtendedKeyFormat.
--
Extended key format is supported since vesion 2.1.12 which should have
long been replaced by a newer version inh all installations. Thus for
2.3 we will make use of the extended-key-format by default.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/card-tool-keys.c: Rename to card-keys.c.
* tools/card-tool-misc.c: Rename to card-misc.c.
* tools/card-tool-yubikey.c: Rename to card-yubikey.c.
* tools/card-tool.h: Rename to gpg-card.h.
* tools/gpg-card-tool-w32info.rc: Rename to gpg-card-w32info.rc
* doc/card-tool.texi: Rename top gpg-card.texi
Signed-off-by: Werner Koch <wk@gnupg.org>
* scd/app-openpgp.c (do_change_pin): Allow prefixing the CHVNO with
"OPENPGP."
* tools/card-call-scd.c (scd_change_pin): Change API to use strings.
* tools/gpg-card-tool.c (cmd_passwd): Adjust for change.
(cmd_unblock): Ditto.
--
The generic keyref allows for better error detection in case a keyref
is send to a wrong card.
Signed-off-by: Werner Koch <wk@gnupg.org>
* kbx/keybox-defs.h (struct _keybox_openpgp_key_info): Add field grip.
* kbx/keybox-openpgp.c (struct keyparm_s): New.
(keygrip_from_keyparm): New.
(parse_key): Compute keygrip.
* kbx/keybox-search.c (blob_openpgp_has_grip): New.
(has_keygrip): Call it.
--
This has been marked for too long as not yet working. However, it is
a pretty useful feature and will come pretty handy when looking for
all keys matching one keygrip.
Can be optimized a lot by storing the keygrip in the meta data. This
will be done along with the upgrade of KBX for v5 fingerprints.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/protect.c (s2k_calibration_time): New file global var.
(calibrate_s2k_count): Use it here.
(get_calibrated_s2k_count): Replace function static var by ...
(s2k_calibrated_count): new file global var.
(set_s2k_calibration_time): New function.
* agent/gpg-agent.c (oS2KCalibration): New const.
(opts): New option --s2k-calibration.
(parse_rereadable_options): Parse that option.
--
Note that using an unrelistic high value (like 60000) takes quite some
time for calibration.
GnuPG-bug-id: 3399
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (parse_list_options): Add option "show-only-fpr-mbox".
* g10/options.h (LIST_SHOW_ONLY_FPR_MBOX): New.
* g10/keylist.c (list_keyblock_simple): New.
(list_keyblock): Call it.
(list_all): Do not print the keyring name in LIST_SHOW_ONLY_FPR_MBOX
mode.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/gpg-wks-client.c (aInstallKey, aRemoveKey, oDirectory): New.
(opts): Add "--install-key", "--remove-key" and "-C".
(parse_arguments): Parse them.
(main): Check that the given directory exists. Implement the new
commands.
--
These commands maybe useful to prepare a WKD directory on a non-Unix
box using the standard wks client.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/gpg-wks.h (opt): Add field with_colons.
* tools/gpg-wks-client.c (oWithColons): New const.
(opts, parse_arguments): Add option --with-colons.
(main): Change aSupported to take several domains in --with-colons
mode.
(command_send): Factor policy getting code out to ...
(get_policy_and_sa): New function.
(command_supported): Make use of new function.
--
In addition to this the --create command now also supports a
submission address only in the policy file. That means the
submission-address file is not anymore required and can be replaced by
the policy file.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/gpg-wks-server.c (opts): Add '--directory',
(main): Explain how to set correct permissions.
(command_list_domains): Create an empty policy file and remove the
warning for an empty policy file.
--
Note that a policy file is meanwhile required and thus is is useful to
create it.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/tdbio.c (tdbio_update_version_record): Never store a TOFU model.
(create_version_record): Don't init as TOFU.
(tdbio_db_matches_options): Don't indicate a change in case TOFU is
stored in an old trustdb file.
--
This change allows to switch between a tofu and pgp or tofu+pgp trust
model without an auto rebuild of the trustdb. This also requires that
the tofu trust model is requested on the command line. If TOFU will
ever be the default we need to tweak the model detection via TM_AUTO
by also looking into the TOFU data base,
GnuPG-bug-id: 4134
* g10/options.h (IMPORT_DROP_UIDS): New.
(EXPORT_DROP_UIDS): New.
* g10/import.c (parse_import_options): Add option "import-drop-uids".
(import_one): Don't bail out with that options and no uids found.
Also remove all uids.
(remove_all_uids): New.
* g10/export.c (parse_export_options): Add option "export-drop-uids".
(do_export_one_keyblock): Implement option.
--
These options are required for experiments with changes to the
keyserver infrastructure.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oKnownNotation): New const.
(opts): Add option --known-notation.
(main): Set option.
* g10/parse-packet.c (known_notations_list): New local var.
(register_known_notation): New.
(can_handle_critical_notation): Rewrite to handle the new feature.
Also print the name of unknown notations in verbose mode.
--
GnuPG-bug-id: 4060
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/import.c (get_revocation_reason): New.
(list_standalone_revocation): Extend function.
--
Note that this function extends the "rvs" field signature-class (field
11) with the revocation reason. GPGME does not yet parse this but it
can be expected that the comma delimiter does not break other parsers.
A new field is added to the "rvs" (and in future also the "rev")
record to carry a record specific comment. Hopefully all parsers
meanwhile learned the lesson from other new fields and don't bail out
on more fields than they know about.
This is partial solution to
GnuPG-bug-id: 1173
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/import.c (impex_filter_getval): Add new "usage" property for
drop-subkey filter.
--
For example, this permits extraction of only encryption-capable
subkeys like so:
gpg --export-filter 'drop-subkey=usage !~ e' --export $FPR
GnuPG-Bug-id: 4019
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* g10/gpg.c (main): Set some list options.
--
The new command --show-keys is commonly used to check the content of a
file with keys. In this case it can be expected that all included
subkeys and uids are of interested, even when they are already expired
or have been revoked.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (aShowKeys): New const.
(opts): New command --show-keys.
(main): Implement command.
* g10/import.c (import_keys_internal): Don't print stats in show-only
mode.
(import_one): Be silent in show-only mode.
--
Using
--import --import-options show-only
to look at a key is too cumbersome. Provide this shortcut and also
remove some diagnostic cruft in this case.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oAllowMultisigVerification)
(oAllowMultipleMessages, oNoAllowMultipleMessages): Remove.
(opts): Turn --allow-multisig-verification, --allow-multiple-messages
and --no-allow-multiple-messages into NOPs
* g10/options.h (struct opt): Remove flags.allow_multiple_messages.
* g10/mainproc.c (proc_plaintext): Assume allow_multiple_messages is
false.
--
These options are very old compatibility hacks and should not be used
anymore. We keep them as dummy options in case someone has them in
the conf file.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c: Make --pgp6 an alias for --pgp7.
* common/compliance.h (gnupg_compliance_mode): Remove CO_PGP6.
* g10/options.h (PGP6): Remove. Adjust all users.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c: Tuen options --force-mdc, --no-force-mdc, --disable-mdc
and --no-disable-mdc into NOPs.
* g10/encrypt.c (use_mdc): Simplify. MDC is now almost always used.
(use_aead): Ignore MDC options. Print warning for missing MDC feature
flags.
* g10/pkclist.c (warn_missing_mdc_from_pklist): Rename to ...
(warn_missing_aead_from_pklist): this and adjust.
--
The MDC is now always used except with --rfc2440 which will lead to a
a big fat warning.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/mainproc.c (proc_encrypted): Require an MDC or AEAD
* tests/openpgp/defs.scm (create-gpghome): Use --ignore-mdc-error to
allow testing with the current files.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oNoMDCWarn): Remove.
(opts): Make --no-mdc-warn a NOP.
(main): Don't set var.
* g10/options.h (struct opt): Remove 'no_mdc_var'.
* g10/cipher-cfb.c (write_header): Assume opt.no_mdc_warn is false.
* g10/mainproc.c (proc_encrypted): Ditto.
--
Users should not be allowed to suppress the warning that they are
shooting into their foot.
Signed-off-by: Werner Koch <wk@gnupg.org>
* dirmngr/http.c (send_request): Print the used TLS library in debug
mode.
--
We allow two different TLS libararies and thus it is useful to see
that in the debug output of bug reports.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/getkey.c (get_user_id_string): Add arg R_NOUID. Change call
callers.
(get_user_id): Add arg R_NOUID. Change call callers.
* g10/mainproc.c (issuer_fpr_string): Make global.
* g10/keylist.c (list_keyblock_colon): Print a '?' for a missing key
also in --list-mode. Print the "issuer fpr" field also if there is an
issuer fingerprint subpacket.
--
Scripts used to rely on the "User ID not found" string even in the
--with-colons listing. However, that is not a good idea because that
string is subject to translations etc. Now we have an explicit way of
telling that a key is missing. For example:
gpg --list-sigs --with-colons | \
awk -F: '$1=="sig" && $2=="?" {if($13){print $13}else{print $5}}'
Prints all keyids or fingerprint of signing keys for which we do not
have the key in our local keyring.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/mainproc.c (issuer_fpr_raw): New.
(issuer_fpr_string): Re-implement using issuer_fpr_rtaw.
(check_sig_and_print): Don't free ISSUER_FPR. Use ISSUER_FPR_RAW.
Use write_status_printf. Extend ERRSIG status.
--
Modern OpenPGP implementations put the ISSUER_FPR into the signature
to make it easier to discover the, public needed to check the
signature. This is also useful in error messages and thus we add it.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oNoSymkeyCache): New.
(opts): Add that option.
(main): Set var.
* g10/options.h (struct opt): New field no_symkey_cache.
* g10/passphrase.c (passphrase_to_dek): Implement that feature.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (oRequestOrigin): New const.
(opts): New option --request-origin.
(main): Parse that option.
* g10/options.h (struct opt): Add field request_origin.
* g10/call-agent.c (start_agent): Send option to the agent.
* sm/gpgsm.c (oRequestOrigin): New const.
(opts): New option --request-origin.
(main): Parse that option.
* sm/gpgsm.h (struct opt): Add field request_origin.
* sm/call-agent.c (start_agent): Send option to the agent.
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/shareddefs.h (request_origin_t): New.
* common/agent-opt.c (parse_request_origin): New.
(str_request_origin): New.
* agent/command.c (option_handler): Implement new option.
--
This allows to pretend that a request originated from the extra or
browser socket.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/cache.c (agent_cache_housekeeping): New func.
* agent/gpg-agent.c (handle_tick): Call it.
--
This change mitigates the risk of having cached items in a post mortem
dump.
GnuPG-bug-id: 3829
Signed-off-by: Werner Koch <wk@gnupg.org>
* tools/gpg-wks-client.c (get_key_status_parm_s)
(get_key_status_cb, get_key): Move to ...
* tools/wks-util.c: ...here.
(get_key): Rename to wks_get_key.
* tools/gpg-wks-server.c: Include userids.h.
(command_install_key): Allow use of a fingerprint.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/gpg.c (opts): Add new option.
(opt_set_iobuf_size): New var.
(set_debug): Set the option.
* tests/openpgp/armor.scm: Use this option to revert the buffer size
to the one which used to exhibit the tested bugs.
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/openpgpdefs.h (PKT_ENCRYPTED_AEAD): New const.
* g10/dek.h (DEK): Increase size of use_aead to 4 bits.
* g10/filter.h (cipher_filter_context_t): Add new fields for AEAD.
* g10/packet.h (PKT_encrypted): Add fields aead_algo, cipher_algo, and
chunkbyte.
* g10/build-packet.c (do_encrypted_aead): New.
(build_packet): Call it.
* g10/parse-packet.c (dump_sig_subpkt): Handle SIGSUBPKT_PREF_AEAD.
(parse_one_sig_subpkt, can_handle_critical): Ditto.
(parse_encrypted): Clear new PKT_ENCRYPTED fields.
(parse_encrypted_aead): New.
(parse): Call it.
* g10/gpg.c (main): Take care of --rfc4880bis option when checking
compliance.
* g10/cipher-aead.c: Replace the stub by real code.
* g10/decrypt-data.c (decode_filter_ctx_t): Add fields for use with
AEAD.
(aead_set_nonce): New.
(aead_set_ad): New.
(decrypt_data): Support AEAD.
(aead_underflow): New.
(aead_decode_filter): New.
* g10/encrypt.c (use_aead): Make that new fucntion work.
(encrypt_simple): Use default_aead_algo() instead of EAX.
* g10/mainproc.c (proc_encrypted): Support AEAD.
(do_proc_packets): Support PKT_ENCRYPTED_AEAD.
--
This code has seen only a very few manual tests. Encrypting always
uses a 64k chunks and decryption has not been tested with larger
chunks. Those small chunks make debugging much faster.
Tests can be done using:
gpg --rfc4880bis --pinentry-mode=loopback --passphrase abc \
--force-aead --aead-algo ocb --s2k-mode 0 --cipher AES \
-v -z 0 --status-fd 2 -c <INFILE >OUTFILE
and
gpg --rfc4880bis --pinentry-mode=loopback --passphrase=abc \
--status-fd 2 -v -d <INFILE >OUTFILE
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/gpg.texi (--passphrase, --passphrase-file, --passphrase-fd):
Note that pinentry-mode needs to be loopback.
Signed-off-by: Andre Heinecke <aheinecke@intevation.de>
* tools/gpgconf.c (oStatusFD): New const.
(opts): New option --status-fd.
(statusfp): New var.
(set_status_fd): New.
(gpgconf_write_status): New.
(gpgconf_failure): New.
(main): Set status fd and replace exit by gpgconf_failure.
* tools/gpgconf-comp.c: Repalce exit by gpgconf_failure.
(gc_process_gpgconf_conf): Print a few warning status messages.
Signed-off-by: Werner Koch <wk@gnupg.org>
* sm/gpgsm.c (main): Allow setting of the default compliance.
* tools/gpgconf-comp.c (gc_options_gpgsm): Add "compliance".
--
This is required so that we can use this option in in gpgconf.conf.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/gpg-agent.c (oListenBacklog): New const.
(opts): New option --listen-backlog.
(listen_backlog): New var.
(main): Parse new options.
(create_server_socket): Use var instead of 5.
* dirmngr/dirmngr.c: Likewise.
* scd/scdaemon.c: Likewise.
--
GnuPG-bug-id: 3473
Signed-off-by: Werner Koch <wk@gnupg.org>
--
The variable definition inside a for statement require to use a c99
option for gcc which we do not want. It has never been used and thus
we drop it.
Signed-off-by: Werner Koch <wk@gnupg.org>
--
A simple read of gpg(1) is ambiguous about whether --encrypt could be
for either symmetric or pubkey encryption. Closer inference suggests
that --encrypt is about pubkey encryption only. Make that clearer on
a first read.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* agent/gpg-agent.c (oAutoExpandSecmem): New enum value.
(opts): New option --auto-expand-secmem.
(main): Implement that option.
--
Note that this option has an effect only if Libgcrypt >= 1.8.2 is
used.
GnuPG-bug-id: 3530
--
A simple read of gpg(1) is ambiguous about whether --encrypt could be
for either symmetric or pubkey encryption. Closer inference suggests
that --encrypt is about pubkey encryption only. Make that clearer on
a first read.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* configure.ac (YAT2M): Only define when found.
* doc/Makefile.am: Portability fix.
--
This is not intended to apply to master, but 2.2 branch only. When
new libgpg-error is required, installation of yat2m can be assumed.
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
--
08c82b1 introduced one optional argument for this status message. Due to
an apparent editing error, the sentence fragment "arguments are
currently defined." was left in the documentation.
Signed-off-by: Will Thompson <wjt@endlessm.com>
--
This answers two questions that I was only able to answer by examining
each site where PROGRESS messages are emitted, and fixes a typo.
Signed-off-by: Will Thompson <wjt@endlessm.com>
* agent/command.c (cmd_getinfo): New sub-commands.
* agent/protect.c (get_standard_s2k_count): Factor some code out to ...
(get_calibrated_s2k_count): new.
(get_standard_s2k_time): New.
Signed-off-by: Werner Koch <wk@gnupg.org>
(cherry picked from commit 52d41c8b0f)
* agent/agent.h (opt): New field 's2k_count'.
* agent/gpg-agent.c (oS2KCount): New enum value.
(opts): New option --s2k-count.
(parse_rereadable_options): Set opt.s2k_count.
--
This option is useful to speed up the starting of gpg-agent and in
cases where the auto-calibration runs into problems due to a broken
time measurement facility.
Signed-off-by: Werner Koch <wk@gnupg.org>
(cherry picked from commit f7212f1d11)
* agent/command.c (cmd_getinfo): New sub-commands.
* agent/protect.c (get_standard_s2k_count): Factor some code out to ...
(get_calibrated_s2k_count): new.
(get_standard_s2k_time): New.
Signed-off-by: Werner Koch <wk@gnupg.org>
* agent/agent.h (opt): New field 's2k_count'.
* agent/gpg-agent.c (oS2KCount): New enum value.
(opts): New option --s2k-count.
(parse_rereadable_options): Set opt.s2k_count.
--
This option is useful to speed up the starting of gpg-agent and in
cases where the auto-calibration runs into problems due to a broken
time measurement facility.
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/import.c (import_one): Pass FROM_SK to list_keyblock_direct.
--
Note that this will likely add the suffix '#' top "sec" because the
secret key has not yet (or will not be) imported. If the secret key
already exists locally another suffix might be printed. The upshot is
that the suffix has no usefulness.
GnuPG-bug-id: 3431
Signed-off-by: Werner Koch <wk@gnupg.org>
* common/pkscreening.c: New.
* common/pkscreening.h: New.
* common/Makefile.am (common_sources): Add them.
* g10/gpg.c (opts): New option --with-key-screening.
* g10/options.h (struct opt): New field with_key_screening.
* g10/keylist.c: Include pkscreening.h.
(print_pk_screening): New.
(list_keyblock_print): Call it.
(print_compliance_flags): Call it.
* sm/gpgsm.c (opts): New option --with-key-screening.
* sm/gpgsm.h (scruct opt): New field with_key_screening.
* sm/keylist.c: Include pkscreening.h.
(print_pk_screening): New.
(print_compliance_flags): Call it. Add new arg cert.
(list_cert_colon): Pass arg cert
(list_cert_std): Call print_pk_screening.
* sm/fingerprint.c (gpgsm_get_rsa_modulus): New.
--
This new option can be used to detect ROCA affected keys. To scan an
entire keyring and print the affected fingerprints use this:
gpg -k --with-key-screening --with-colons | gawk -F: \
'$1~/pub|sub|sec|ssb|crt/ && $18~/\<6001\>/ {found=1;next};
$1=="fpr" && found {print $10}; {found=0}'
The same works for gpgsm. Note that we need gawk due to the "\<" in
the r.e.
Signed-off-by: Werner Koch <wk@gnupg.org>
--
It seems people are using --list-sigs instead of --check-sigs and do
not realize that the signatures are not checked at all. We better
highlight the use of --check-sigs to avoid this UI problem.
Suggested-by: Andrew Gallagher
Signed-off-by: Werner Koch <wk@gnupg.org>
--
It seems people are using --list-sigs instead of --check-sigs and do
not realize that the signatures are not checked at all. We better
highlight the use of --check-sigs to avoid this UI problem.
Suggested-by: Andrew Gallagher
Signed-off-by: Werner Koch <wk@gnupg.org>
* doc/Makefile.am: Move qualified.txt into examples.
* doc/qualified.txt: Move into examples, remove trailing spaces.
* doc/examples/README: Document qualified.txt.
* doc/gpgsm.texi: Move qualified.txt from datadir into sysconfdir.
* sm/qualified.c (read_list): Move qualified.txt from datadir into
sysconfdir.
--
The qualified.txt is maintained by Administrator it is a configuration
file. In the past it was a hybrid, provided by package and controlled
by the Administrator, however, it is no longer maintained by package.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
* agent/command.c (hlp_genkey): update help text to suggest the use of
3072 bits.
* doc/wks.texi: Make example match default generation.
* g10/keygen.c (DEFAULT_STD_KEY_PARAM): update to
rsa3072/cert,sign+rsa3072/encr, and fix neighboring comment,
(gen_rsa, get_keysize_range): update default from 2048 to 3072).
* g10/keyid.c (pubkey_string): update comment so that first example
is the default 3072-bit RSA.
--
3072-bit RSA is widely considered to be 128-bit-equivalent security.
This is a sensible default in 2017.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
Gbp-Pq: Topic update-defaults
Gbp-Pq: Name 0015-gpg-default-to-3072-bit-RSA-keys.patch
* doc/gpgsm.texi, doc/howto-create-a-server-cert.texi: : update
default to 3072 bits.
* sm/certreqgen-ui.c (gpgsm_gencertreq_tty): update default to
3072 bits.
* sm/certreqgen.c (proc_parameters): update default to 3072 bits.
* sm/gpgsm.c (main): print correct default_pubkey_algo.
--
3072-bit RSA is widely considered to be 128-bit-equivalent security.
This is a sensible default in 2017.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
Gbp-Pq: Topic update-defaults
Gbp-Pq: Name 0014-gpgsm-default-to-3072-bit-keys.patch
* g10/gpg.c (main): remove KEYSERVER_AUTO_KEY_RETRIEVE from the
default keyserver options.
* doc/gpg.texi: document this change.
--
This is a partial reversion of
7e1fe791d1. Werner and i discussed it
earlier today, and came to the conclusion that:
* the risk of metadata leakage represented by a default
--auto-key-retrieve, both in e-mail (as a "web bug") and in other
contexts where GnuPG is used to verified signatures, is quite high.
* the advantages of --auto-key-retrieve (in terms of signature
verification) can sometimes be achieved in other ways, such as when
a signed message includes a copy of its own key.
* when those other ways are not useful, a graphical, user-facing
application can still offer the user the opportunity to choose to
fetch the key; or it can apply its own policy about when to set
--auto-key-retrieve, without needing to affect the defaults.
Note that --auto-key-retrieve is specifically about signature
verification. Decisions about how and whether to look up a key during
message encryption are governed by --auto-key-locate. This change
does not touch the --auto-key-locate default of "local,wkd". The user
deliberately asking gpg to encrypt to an e-mail address is a different
scenario than having an incoming e-mail trigger a potentially unique
network request.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* doc/gpg.texi: Document new option.
* g10/call-dirmngr.c (create_context): Fail if option is given.
* g10/gpg.c (cmd_and_opt_values): New value.
(opts): New option.
(gpgconf_list): Add new option.
(main): Handle new option.
* g10/options.h (struct opt): New field 'disable_dirmngr'.
* tools/gpgconf-comp.c (gc_options_gpg): New option.
GnuPG-bug-id: 3334
Signed-off-by: Justus Winter <justus@g10code.com>
* doc/examples/systemd-user/*.service: Drop redundant After=*.socket
directive.
--
systemd.socket(5) says:
Socket units will have a Before= dependency on the service which
they trigger added implicitly.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* doc/examples/systemd-user/*.service: drop RefuseManualStart=true
--
These user services can be safely started manually as long as at least
their primary sockets are available. They'll just start with nothing
to do, which should be fine.
Signed-off-by: Daniel Kahn Gillmor <dkg@fifthhorseman.net>
* g10/gpg.c (main): Add KEYSERVER_AUTO_KEY_RETRIEVE to the default
keyserver options. Set the default for --auto-key-locate to
"local,wkd". Reset that default iff --auto-key-locate has been given
in the option file or in the commandline.
* g10/getkey.c (parse_auto_key_locate): Work on a copy of the arg.
--
GnuPG-bug-id: 3324
Signed-off-by: Werner Koch <wk@gnupg.org>
* g10/options.h (IMPORT_DRY_RUN): New.
* g10/import.c (parse_import_options): Add "show-only".
(import_one): use that as alternative to opt.dry_run.
--
This is just a convenience thing for
--import-options import-show --dry-run
Signed-off-by: Werner Koch <wk@gnupg.org>
--
dev.gnupg org is the development platform but the canonical bug
address is and has always been bugs.gnupg.org. We should keep on
using this address for the case that we switch the tracker again or
split it off the development system.
That is also the reason why we should keep on communicating a plain
bug number without the 'T' prefix.
Signed-off-by: Werner Koch <wk@gnupg.org>
